收藏本站
Preliminary Technical Data
EVAL-ADM106x
The sequence will enter the state where this command has
been selected and wait for an SMBus Jump command to
be issued by the user
Unconditional timeout
When SMBus Jump is
selected a symbol is
placed on the far left
of the ‘Sequencing
Engine Program’
Pressing this button
will issue the
SMBus Jump
command
Figure 50. Programming an unconditional Timeout
PROGRAMMING THE MONITOR FUNCTION
Figure 48. SMBus Jump
PROGRAMMING THE TIMEOUT FUNCTION
Programming the Timeout event is the opposite of programming
the Sequence. It takes the format “ IF event has NOT occurred
AFTER Xms THEN GOTO StateX. The software automatically
generates most of the statement. The only programmable elements
are the length of the timeout and the State to exit to.
The Monitor function, as described above, is a wide OR gate
whose inputs are the status of all of the ADM106x’s inputs,
including the ADC inputs (these are OR’ed together prior to
this and output a single WARNING function). The user can
select which inputs are to be monitored in a given state, and the
polarity that input must assert before action is taken. The action
taken is to GOTO another state. Again, the user can select
which state to go to.
Note: The supply fault detectors assert a 1 when a fault is
detected. When programming the Monitor function the user
should select “IF <INPUT = 1>” if they want action to be
taken when a supply goes out of tolerance. The software will
indicate if the VXn is in digital or analog mode by displaying
Hi/Lo if the VXn input is set to a digital mode and OK/FLT if it
is set to analog mode.
Click to enable
Timeout
The timeout statement
is the inverse of the
sequence statement
The programming of the Monitor function is shown below.
Figure 49. Programming the Timeout
The Timeout function can also be programmed independently of the
Sequence function. In this case there will be an unconditional
timeout before moving to the next state. The user can program this
simply to put an extended delay between one event and the next
occurring. The maximum timeout delay is 400ms, but if a delay
longer than this is required, the user can cascade a number of states
Click to enable
monitor
Select Hi/Lo or OK/FLT using these
drop down boxes. N.B. Fault(FLT) = 1
together, setting the Timeout in each state.
Figure 51. Programming the Monitor Function
Programming the Monitor function can also be done
independently of the Sequence or Timeout function. For
instance, once a power up sequence is completed, the user may
Rev. PrB | Page 27 of 38
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADM1075CEBZ BOARD EVAL FOR ADM1075
EVAL-ADM1087EBZ BOARD EVALUATION FOR ADM1087
EVAL-ADM1166TQEBZ BOARD EVAL FOR ADM1166TQ
EVAL-ADM1168LQEBZ BOARD EVAL FOR ADM1168LQ
EVAL-ADM1170EBZ BOARD EVALUATION FOR ADM1170
EVAL-ADM1171EBZ BOARD EVALUATION FOR ADM1171
EVAL-ADM1172EBZ BOARD EVALUATION FOR ADM1172
EVAL-ADM1175EBZ BOARD EVALUATION FOR ADM1175
相关代理商/技术参数
EVAL-ADM1063LFEB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADM1063LFEBZ 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADM1063TQEB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADM1063TQEBZ 功能描述:BOARD EVALUATION FOR ADM1063TQ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1064LFEB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADM1064LFEBZ 制造商:Analog Devices 功能描述:EVAL KIT FOR ADM1064 - Bulk
EVAL-ADM1064TQEB 功能描述:BOARD EVALUATION FOR ADM1064TQ RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1064TQEBZ 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk